Audio Related Topics

Elton John Amy

Stained Could It Be

Thump is one thing, but should not be overly loud. I would put a scope on the +/-rails, one set at a time, starting with the highest voltage rails. Do they decay/bleed down at the same rate? They should look about the same, but opposite polarity. Whats likely happening is that the +/-12V decay at much different rates, this causes the input opamp to rail in one direction or the other, creating a large transition at the output. Since the +/-12V are derived from the higher voltage rails, it's likely that one of them is the culprit.

Welcome!

Dire Straits Private Investigations

KORN Falling Away From Me

Welcome from VA! Enjoy your stay! While it's possible it could be something else, it is very likely just the "thump" that is typically found in these amps. Power supply caps can contribute so be sure to replace those with some high quality types.

Whatever

The smarta$$ in me says: Reverend Raymond Daniel Oh . . . Ray D.Oh, that is! The high priest of rhthmic noise . . .

A friend turned me on to Louis Prima. Ever hear of him? Pretty crazy good stuff. I guess his Las Vegas recording is good too. Sounds to me that they are having a damn good time playing their music.

Was on quite a Coltrane kick a while back after my Chet Baker kick. Now on a Bill Evans kick. Doing all of these with tubes but the Coltrane stuff and detail somehow sounds better with SS.

Red Garland on piano, Paul Chambers on bass, and Art Taylor on drums. AI generated answer. I'm too lazy to dig up the disc. I'm playing the DSD files from my NAS. They sound great through the WiiM, 4000t, M500t mkII, the Martin Logans and SVS sub.

That dude could play!!! Have to also look up who the bass and piano guys were on that one. Thanks. Good one!!!!

John Coltrane, Soultrane MFSL SACD

What a great "second opportunity" for you!!! Welcome, great to have you with us.

Hello everybody. I found an M–1.0t a at Goodwill a few years ago. Long before I had the confidence to work on it myself. It did not work so I sold it not working. Always wondering what I was missing out on. Well, last week I came across another one with a C1 preamp and tuner. It of course also didn’t work, but this time I am determined to fix it. So after some troubleshooting, I found that the PreDrivers were shorted on both channels preventing it from powering on all the way. I have since replaced those, it powered up all voltages were good. I set the Bias and have been listening all day. It sounds great and I’m glad I was able to find another one. However, I have a very loud pop in the speakers about 5 seconds after I switch off the amplifier. It seems that the longer it is powered on the louder the “pop” I have read the service bulletin about the the “turn on / turn off thump” and I’ve ordered the parts to complete the repair however, my question is, is THAT noise THE thump? I have heard amplifiers thump before, but this was a very loud pop. I wouldn’t describe it as a low. I have a hard time believing this “thump fix“ is going to take care of this. Also. this is a Non-inverting model Any insight would be greatly appreciated. Thank you so much.

Beastie Boys She's Crafty

hello, I kinda fell into some Sunfire gear recently. I’ve been doing my best at using the resources available to me here on the carver site.com, but, as I’m sure you’re aware there are many similar models of most of these amps. my first DIY is to replace the lamp for the joules meter. I think I’ve found one on eBay, but I like to buy parts in multiples or bulk if possible. I can’t locate the specs for the lamp. I forgot to measure voltage when I had it open, and I can’t measure the milliamps at hand. I’ve found axial 12volt 100ma bulbs in bulk, the ones marketed towards Sunfire units are much pricier and sold singly. any info is greatly appreciated thanks

The Cure Friday I'm In Love

Eagles Chug All Night (2013 Remastered)

The Offspring Hammerhead